- 您现在的位置：买卖IC网 > Sheet目录861 > GRM43DR61E106KA12L (Murata Electronics North America)CAP CER 10UF 25V 10% X5R 1812
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
! Caution
Continued from the preceding page.
<Applicable to GMA or GMD Series>
9. Die Bonding/Wire Bonding
C02E.pdf
Sep.25,2013
1. Die Bonding of Capacitors
1-1. Use the following materials for the Brazing alloys:
Au-Sn (80/20) 300 to 320 °C in N 2 atmosphere
1-2. Mounting
(1) Control the temperature of the substrate so it
matches the temperature of the brazing alloy.
(2) Place the brazing alloy on the substrate and place
the capacitor on the alloy. Hold the capacitor and
gently apply the load. Be sure to complete the
operation within 1 minute.
c Other
1. Under Operation of Equipment
1-1. Do not touch a capacitor directly with bare hands
during operation in order to avoid the danger of an
electric shock.
1-2. Do not allow the terminals of a capacitor to come in
contact with any conductive objects (short-circuit).
Do not expose a capacitor to a conductive liquid,
including any acid or alkali solutions.
1-3. Confirm the environment in which the equipment will
operate is under the specified conditions.
Do not use the equipment under the following
environments.
(1) Being spattered with water or oil.
(2) Being exposed to direct sunlight.
(3) Being exposed to ozone, ultraviolet rays, or
radiation.
(4) Being exposed to toxic gas (e.g., hydrogen sulfide,
sulfur dioxide, chlorine, ammonia gas, etc.)
(5) Any vibrations or mechanical shocks exceeding the
specified limits.
(6) Moisture condensing environments.
1-4. Use damp proof countermeasures if using under any
conditions that can cause condensation.
2. Other
2-1. In an Emergency
(1) If the equipment should generate smoke, fire, or
smell, immediately turn off or unplug the equipment.
If the equipment is not turned off or unplugged, the
hazards may be worsened by supplying continuous
power.
(2) In this type of situation, do not allow face and
hands to come in contact with the capacitor or
burns may be caused by the capacitor's high
temperature.
152
2. Wire Bonding
2-1. Wire
Gold wire: 25 micro m (0.001 inch) diameter
2-2. Bonding
(1) Thermo compression, ultrasonic ball bonding.
(2) Required stage temperature: 150 to 200 °C
(3) Required wedge or capillary weight: 0.2N to 0.5N
(4) Bond the capacitor and base substrate or other
devices with gold wire.
2-2. Disposal of Waste
When capacitors are disposed of, they must be
burned or buried by an industrial waste vendor with
the appropriate licenses.
2-3. Circuit Design
(1) Addition of Fail Safe Function
Capacitors that are cracked by dropping or
bending of the board may cause deterioration of
the insulation resistance, and result in a short.
If the circuit being used may cause an electrical
shock, smoke or fire when a capacitor is shorted,
be sure to install fail-safe functions, such as a
fuse, to prevent secondary accidents.
(2) Capacitors used to prevent electromagnetic
interference in the primary AC side circuit, or as a
connection/insulation, must be a safety standard
certified product, or satisfy the contents stipulated
in the Electrical Appliance and Material Safety
Law. Install a fuse for each line in case of a short.
(3) The GJM, GMA, GMD, GQM, GR3, GRJ, GRM,
KR3, KRM, LLA, LLL, LLM and LLR series are
not safety standard certified products.
2-4. Remarks
Failure to follow the cautions may result, worst case,
in a short circuit and smoking when the product is
used.
The above notices are for standard applications and
conditions. Contact us when the products are used in
special mounting conditions.
Select optimum conditions for operation as they
determine the reliability of the product after assembly.
The data herein are given in typical values, not
guaranteed ratings.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
H-22-3A
DIAL SCALE 15 TURN CONCENTRIC
H-23-6M
DIAL SCALE 15 TURN CONCENTRIC
H-26S
SIDE BRACKET FOR MODEL 3250/3252
H-46-6A
COUNTING DIAL 0-20 TURNS
H-83P
RETRO FIT PANEL MNT HOLDER
H472K47X7RL6VJ5R
CAP CER 4700PF 500V 10% RADIAL
HA55L-4523500LF
INDUCTOR POWER 50UH
HB01U05S05YC
CONV DC/DC 5V 200MA UNREGUL
相关代理商/技术参数
GRM43DR61E106MA12L
制造商:Murata Manufacturing Co Ltd 功能描述: 制造商:Murata Manufacturing Co Ltd 功能描述:CAP,CERAMIC CHIP,10UF,25VDC,20%,SMD,1812-CASE
GRM43DR71H155KA01L
功能描述:CAP CER 1.5UF 50V 10% X7R 1812 RoHS:是 类别:电容器 >> 陶瓷 系列:GRM 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:-
GRM43DR71H155MA01L
功能描述:CAP CER 1.5UF 50V 20% X7R 1812 RoHS:是 类别:电容器 >> 陶瓷 系列:GRM 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:-
GRM43DR72A155KA01L
功能描述:多层陶瓷电容器MLCC - SMD/SMT 1812 1.5uF 100volts X7R 10% RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
GRM43DR72A155MA01L
功能描述:多层陶瓷电容器MLCC - SMD/SMT 1812 1.5uF 100volts X7R 20% RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
GRM43DR72A334KW01L
制造商:Murata Manufacturing Co Ltd 功能描述:
GRM43DR72A474KA01L
功能描述:多层陶瓷电容器MLCC - SMD/SMT 1812 0.47uF 100volts 10% RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
GRM43DR72A474KW01L
制造商:Murata Manufacturing Co Ltd 功能描述: